| |
 |
|
|
|
 |
 |
|
 |
| Rutland
913 Windcharger |
Marlec’s 913 Marine Mounting Kit
is manufactured from stainless steel
and is supplied in 2 x 1.2m sections
that join. Deck fixing L shaped
plates are supplied along with brackets
to which guys or stays should be
attached. Solid stays are recommended
to provide a suitably rigid mount
for the windcharger.
A pole
can be constructed for deck fixing
using a continuous length of the
tube, a minimum 2.5m length is recommended.
Note that the mounting tube dimensions
must be 41mm internal diameter and
no more than 48mm outer diameter.
Also available are single 1200mm
and 600mm tube sections for the
user to adapt to their own mounting
design. |
| Rutland
503 Windcharger |
Marlec’s
503 Marine Mounting Kit is manufactured
from stainless steel and is supplied
in 2 x 1m sections that join. Deck
fixing L shaped plates are supplied
along with brackets to which guys
or stays should be attached. Solid
stays are recommended to provide
a suitably rigid mount for the windcharger.
A pole can be constructed for deck
fixing using a continuous length
of the tube, a minimum 2.5m length
is recommended. Note that the mounting
tube dimensions must be 31.7mm internal
diameter and no more than 38mm outer
diameter.Also available are single
1m and 500mm tube sections for the
user to adapt to their own mounting
design |
|
|
| Rutland
503 Windcharger |
The
Rutland 503 may be used for temporary
installation on land, for example
on touring caravans or rv’s.
The Rutland 503 Land Tower Kit
and Rigging Kit provides a 4m
total height tower supplied in
2 sections with joiner. A pole
ground-spike is supplied and
6 anchors for the 6 guy ropes,
turnbuckles, etc are also supplied.
This tower is not for permanent
installation!
Supplied as:
503 Tower Kit - CA-12/12
2 x 2m sections of 35mm o/d polished
stainless steel tube with tube joiner and
ground fixing spike. To be installed with
Tower Rigging Kit.
Overall height 4 metres
Tower Rigging Kit . CA-12/13
Consists of 2 sets of 3 guy wires ready
fitted to the tower attachments for upper
and lower sections, shackles and
ground anchors. The guys are
polypropylene covered galvanised steel
and all steel parts are plated for weather
protection.
|
 |
| Rutland 913 and Furlmatic 910-3 Windcharger |
The Rutland 913 may be used for
temporary installation on land,
for example on touring caravans,
rv’s or summer season installed
static caravans. For permanent installations
the Rutland Furlmatic 910-3 model
is recommended.
The
FM910-3 may be used for permanent
or temporary installation on land.
It is not suitable for use on unstable
platforms, eg floating buoys as
the furling mechanism is affected
by rolling motion. Stable platforms
eg, oil rigs, are suitable.
The Rutland 910 series Land Tower
Kit and Rigging Kit provides a 6m
total height tower supplied in 3
sections with joiners. A pole ground-spike
is supplied and 4 anchors for the
8guy ropes, turnbuckles, etc are
also supplied. This tower pivots
for easy installation and lowering
and is for permanent installation!
A tower can be constructed using
a pole of minimum height 6m with
an internal diameter of 41mm. Guy
ropes or supports should always
be used to ensure the tower is rigid.
The final height of the turbine
should be determined by the site
and is discussed in the installation
manuals provided.
Supplied as:
Tower Kit - 910 Series
–6.4m (3 x 2.13m sections) of 48mm dia galvanised steel tube ready drilled for assembly complete with joiners. Suitable for use with Rutland 913 or FM910-3 (with adaptor).
CA-12/08
Tower Rigging Kit-910 Series–complete with steel guys, shackles, turnbuckles, pole
attachments, ground fixings for
pole and guys. (designed for
permanent installation-concrete
base for pole and guy anchors
recommended)
CA-12/07
|
|
| Rutland
Furlmatic 1803 Windcharger |
The
FM1803 may be used as a permanent
or temporary installation on land
on appropriate type mounting structures.
It is not suitable for use on unstable
platforms, eg floating buoys as
the furling mechanism is affected
by rolling motion. Stable platforms
eg, oil rigs, are suitable.
- The minimum recommended
height is between 6-10m but
the height should ultimately
be determined by the location
depending on the openness of
the site taking into account
turbulence caused by trees,
builings, undulating hills,etc.
- A tower
can be constructed using
a pole of minimum height
6m with an internal diameter
of 81mm (3” or 91mm outside
diameter tube is usually suitable).
Guy ropes or supports should
always be used to ensure the
tower is rigid, 2 sets each
of 4 wires, one set just below
the blade line and the other
at half the tower height should
be regarded as a minimum requirement.
- Alternative
towers are available from specialist
manufacturers eg lattice type
towers, or columns from street
light manufacturers. In each
case it is preferable to select
a tower with a hinge to facilitate
lowering.
-
Contact Marlec for more information about towers.
|
|
|
|
|
|
| |
|
